Home |
Search |
Today's Posts |
#1
|
|||
|
|||
Coaxial power cable, etc?
I'm looking at some PA amp designs (300-500W).
Amp layouts often use or specify twisted power wiring to partly cancel magnetic fields. Would a co-axial power cable (if available, otherwise, two pairs of wire twisted together) improve on this, since a twist has a limited pitch? Another related question. In high-power amps, a layout technique referred to as "distortion cancelling" is being used. Again, this aims to reduce the coupling of magnetic fields from high-current PCB traces back into the input stages. I understand the principle, but what's the actual technique - what geometries are effective? Is it just a matter of minimising the loop area, and if so, could the loop traces be run on opposite sides of the PCB to do that? Can you point me to any tutorial-type resources on this type of layout? Clifford Heath. |
#2
|
|||
|
|||
Clifford Heath wrote:
Amp layouts often use or specify twisted power wiring to partly cancel magnetic fields. Would a co-axial power cable (if available, otherwise, two pairs of wire twisted together) improve on this, since a twist has a limited pitch? No. Electrostatic shields don't do anything against magnetic fields, which are the main problem at those distances and frequencies. Twisting the conductors is very effective (and dates back at least to the era of filament wiring). Another related question. In high-power amps, a layout technique referred to as "distortion cancelling" is being used. Again, this aims to reduce the coupling of magnetic fields from high-current PCB traces back into the input stages. I understand the principle, but what's the actual technique - what geometries are effective? Is it just a matter of minimising the loop area, and if so, could the loop traces be run on opposite sides of the PCB to do that? Can you point me to any tutorial-type resources on this type of layout? That just sounds like reasonable PC board layout precautions more than anything else. Doug Self's series of articles on amplifier design in Wireless World touches on it, but it's not one of the more significant distortion sources. It might be in an amp with transformer coupling, though. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#3
|
|||
|
|||
Scott Dorsey wrote:
No. Electrostatic shields don't do anything against magnetic fields, I wasn't thinking of electrostatics, but magnetics. A coaxial cable should have almost zero magnetic field in any direction and scale, even less than twisted pair. Shouldn't it? Or is that true, but the effect is too small to matter? The way I figure it, if you have a 1" twist pitch, then any component within 1/2" which is sensitive to pickup will see significant magnetic field despite the twist, which shouldn't be the case with co-ax. Obviously it's best to keep such high current wiring away from such components, but anyhow... That just sounds like reasonable PC board layout precautions more than anything else. Doug Self's series of articles on amplifier design in Wireless World touches on it, but it's not one of the more significant distortion sources. It might be in an amp with transformer coupling, though. Thanks for that. I'm thinking of the more recent Silicon Chip magazine amps, which claim much lower distortion than earlier amps (like ETI466, PM300, etc) due to better PCB layout. I don't have the text of the mag articles where they argue this, and in any case I recall it was a discussion on principle, not "this track is laid here rather than there for this reason". Clifford Heath. |
#4
|
|||
|
|||
"Clifford Heath" Another related question. In high-power amps, a layout technique referred to as "distortion cancelling" is being used. Again, this aims to reduce the coupling of magnetic fields from high-current PCB traces back into the input stages. I understand the principle, but what's the actual technique - what geometries are effective? Is it just a matter of minimising the loop area, and if so, could the loop traces be run on opposite sides of the PCB to do that? ** Any loop areas associated with the input signal, input ground and feedback ground need to be kept small as possible. The problem is with class B output stages where the DC supply current to the output devices very distorted ( half sine shape) and harmonics can become injected in the loops mentioned - which ruins the THD specs particularly at the higher audio frequencies. Just as undesirable is the case of a stereo amp where the same distorted current injection transfers from one channel to the other - producing distorted crosstalk. Close up those loops and keep the high current DC wiring well away from them and you can beat it. ........... Phil |
#5
|
|||
|
|||
On Wed, 25 Aug 2004 12:32:20 +1000, Clifford Heath
wrote: Scott Dorsey wrote: ... That just sounds like reasonable PC board layout precautions more than anything else. Doug Self's series of articles on amplifier design in Wireless World touches on it, but it's not one of the more significant distortion sources. It might be in an amp with transformer coupling, though. Thanks for that. I'm thinking of the more recent Silicon Chip magazine amps, which claim much lower distortion than earlier amps (like ETI466, PM300, etc) due to better PCB layout. I don't have the text of the mag articles where they argue this, and in any case I recall it was a discussion on principle, not "this track is laid here rather than there for this reason". There's the 'principle" that PCB traces have non-zero resistance. Google for Douglas Self's website. ISTR that's one of his eight things that cause distortion is bad layout, specifically where the feedback point is placed - he has schematics where he says you run the feedback path from 'here' (the speaker terminal) rather than 'here' (the junction of the output transistors), even though 'electrically' they're the same, but on a practical PCB and chassis, they're not. He'll want to sell you his book, too, which is likely to be interesting as well. Clifford Heath. ----- http://mindspring.com/~benbradley |
#6
|
|||
|
|||
Ben Bradley wrote:
On Wed, 25 Aug 2004 12:32:20 +1000, Clifford Heath wrote: Scott Dorsey wrote: ... That just sounds like reasonable PC board layout precautions more than anything else. Doug Self's series of articles on amplifier design in Wireless World touches on it, but it's not one of the more significant distortion sources. It might be in an amp with transformer coupling, though. Thanks for that. I'm thinking of the more recent Silicon Chip magazine amps, which claim much lower distortion than earlier amps (like ETI466, PM300, etc) due to better PCB layout. I don't have the text of the mag articles where they argue this, and in any case I recall it was a discussion on principle, not "this track is laid here rather than there for this reason". There's the 'principle" that PCB traces have non-zero resistance. Google for Douglas Self's website. ISTR that's one of his eight things that cause distortion is bad layout, specifically where the feedback point is placed - he has schematics where he says you run the feedback path from 'here' (the speaker terminal) rather than 'here' (the junction of the output transistors), even though 'electrically' they're the same, but on a practical PCB and chassis, they're not. The flip side might be stability. He'll want to sell you his book, too, which is likely to be interesting as well. Clifford Heath. ----- http://mindspring.com/~benbradley -- The e-mail address in our reply-to line is reversed in an attempt to minimize spam. Our true address is of the form . |
#7
|
|||
|
|||
Phil Allison wrote:
** Any loop areas associated with the input signal, input ground and feedback ground need to be kept small as possible. Thanks Phil, I thought it was that simple. On the other hand, ISTR that SC played with the shape and position of the traces around the OP transistors to reduce or cancel the magnetic fields, perhaps by running the collector and emittor traces equidistant from a ground trace so that current outbound to any OP transistor and current inbound each cause magnetic fields due to their ground-loop shape, and the two fields cancel so neither reaches the input stage in any quantity. The principle is sound, but the recent (Jan 04) design doesn't use the obvious method (outgoing and incoming traces on the same side above a ground plane), and I wondered if anyone could explain the rationale for what they *did* do. Or if my proposal is correct either... Maybe SC just wanted to avoid a double-sided PCB? I think I just explained to myself what it was I was originally asking about. Hope it makes sense to someone else also. Thanks to Ben also. I had already come across the concept of carefully placing the feedback takeoff point, it's not what I had in mind, though obviously important. I feel more confident about proceeding with my high-power bass guitar amp design now. Clifford Heath. |
#8
|
|||
|
|||
"Clifford Heath" Phil Allison wrote: ** Any loop areas associated with the input signal, input ground and feedback ground need to be kept small as possible. Thanks Phil, I thought it was that simple. ** The idea is simple - but maybe not so simple to achieve when you have to build a low THD amp. The PCB pattern and cabling layouts can go through many iterations before the desired specs are reliably met by a product - the proof is a good looking ( mainly 2H and 3 H ) residual on a scope after filtering out the fundamental at say 6 kHz - and that displacing the various input and high current cables slightly does not harm this. With a stereo amp one can just look at the HF crosstalk on a scope for any signs of harmonics - they have the same cause. ........... Phil |
#9
|
|||
|
|||
Ben Bradley wrote:
On Wed, 25 Aug 2004 12:32:20 +1000, Clifford Heath wrote: Scott Dorsey wrote: That just sounds like reasonable PC board layout precautions more than anything else. Doug Self's series of articles on amplifier design in Wireless World touches on it, but it's not one of the more significant distortion sources. It might be in an amp with transformer coupling, though. Thanks for that. I'm thinking of the more recent Silicon Chip magazine amps, which claim much lower distortion than earlier amps (like ETI466, PM300, etc) due to better PCB layout. I don't have the text of the mag articles where they argue this, and in any case I recall it was a discussion on principle, not "this track is laid here rather than there for this reason". There's the 'principle" that PCB traces have non-zero resistance. Very much so ! I find it easier to consider traces as being resistors. That way, the sources of error are easy to spot. Google for Douglas Self's website. ISTR that's one of his eight things that cause distortion is bad layout, specifically where the feedback point is placed - he has schematics where he says you run the feedback path from 'here' (the speaker terminal) rather than 'here' (the junction of the output transistors), even though 'electrically' they're the same, but on a practical PCB and chassis, they're not. The example of the positioning of the feedback node is an excellent one. I recently had occasion to ask a pcb layout guy to move this point for precisely the reasons you state. Good layout also defines and constrains current paths - especially important with high currents. Graham |
#10
|
|||
|
|||
"Clifford Heath" wrote in message
I'm looking at some PA amp designs (300-500W). Amp layouts often use or specify twisted power wiring to partly cancel magnetic fields. Would a co-axial power cable (if available, otherwise, two pairs of wire twisted together) improve on this, since a twist has a limited pitch? The *signal* on a power cable can be thought of as being balanced. Therefore, the use of twisted pair is indicated. Another related question. In high-power amps, a layout technique referred to as "distortion cancelling" is being used. AFAIK, the most obvious example of this principle was the input wiring on the original DH-200 Mosfet power amp, where routing this lead in accordance with the directions reduced THD @20 KHz by at least 50%. Again, this aims to reduce the coupling of magnetic fields from high-current PCB traces back into the input stages. In the case I'm thinking of, the coupling was manipulated seemed to be electrostatic coupling. I think that either kind of coupling could be either controlled or avoided to minimize distortion. I understand the principle, but what's the actual technique - what geometries are effective? I can tell you how to minmize coupling, but minimizing coupling need not be the best approach. If some specific kind of coupling is required, then the means used are going to be specific to the particular design. Is it just a matter of minimising the loop area, and if so, could the loop traces be run on opposite sides of the PCB to do that? That could be a means that would be used to minimize coupling. However, small circuit traces on the same side of the board can be closer together than the thickness of the board. Can you point me to any tutorial-type resources on this type of layout? http://www.zilog.com/docs/z8/appnote...mizing_emi.pdf http://www.lcr-inc.com/whitepapers/E...c_Coupling.pdf http://www.chrontel.com/pdf/an36.pdf http://www.rfm.com/products/apnotes/an42.pdf http://www.maxim-ic.com/appnotes.cfm/appnote_number/735 http://www.elmac.co.uk/c_e_layt.htm |
#11
|
|||
|
|||
Clifford Heath wrote:
Scott Dorsey wrote: No. Electrostatic shields don't do anything against magnetic fields, I wasn't thinking of electrostatics, but magnetics. A coaxial cable should have almost zero magnetic field in any direction and scale, even less than twisted pair. Shouldn't it? No. Why would putting an electrostatic shield around a wire do anything about the magnetic leakage issues? Remember, you are talking about something that isn't operating as a transmission line, so all of the constant impedance stuff is basically out the window. It's just a wire with an electrostatic shield since you're way below a full wave length. Thanks for that. I'm thinking of the more recent Silicon Chip magazine amps, which claim much lower distortion than earlier amps (like ETI466, PM300, etc) due to better PCB layout. I don't have the text of the mag articles where they argue this, and in any case I recall it was a discussion on principle, not "this track is laid here rather than there for this reason". What does that mean? Lower THD doesn't really matter much by itself. You care more about the kind of distortion than the amount of distortion most of the time these days. --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#12
|
|||
|
|||
In rec.audio.pro Scott Dorsey wrote:
: No. Why would putting an electrostatic shield around a wire do : anything about the magnetic leakage issues? Remember, you are talking : about something that isn't operating as a transmission line, so all : of the constant impedance stuff is basically out the window. It's just : a wire with an electrostatic shield since you're way below a full wave : length. If the shield is the return path for the current in the wire, the magnetic fields of the wire and shield exactly cancel outside of the shield; all of the B field is completely enclosed by the shield -- assuming perfectly centered wire in a perfectly cylindrical, uniformly conducting shield... Twisted pair is usually used because it is almost as good for most situations and a lot cheaper. Bob Miller |
#13
|
|||
|
|||
|
#15
|
|||
|
|||
In rec.audio.pro Clifford Heath wrote:
: Twisted four (two hots and two grounds in a square x-section with each : pair diagonally opposite) should be even better than twisted pair : (nearly complete cancellation because the AB on this side is cancelled : by the BA on the other) but still at a fairly low cost... no? Yes. But all of this starts to run afoul of electrical codes for flexible cables. You have to have a ground in there, usually. Cable which is 4-wire plus ground can be had (for a price -- it gets used for some "wye" three-phase power applications), but the fifth wire will distort the "star-quad" arrangement. It also may be difficult to safely wire two conductors into each connection point on the connectors. : BTW, are you the same guy that did atomic clocks for HP? : I remember admiring posts about that a few years back. Naah. I do 6.25GHz serial HW today, have done graphics engines and IEEE floating-point math hardware in the past... Glad you recognized the "Bill and Dave" association in my (munged) email address ;-) Bob Miller Agilent Technologies |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
A Couple of questions on audioquest power cords and CD-Rs | Tech | |||
rec.audio.car FAQ (Part 2/5) | Car Audio | |||
FS: 3000 watt amp $179!! 900 watt woofers $36!! new- free shipping | General | |||
Power cable | Car Audio | |||
Quad snake cable | Pro Audio |